XADO gel for Petrol/LPG engine

Single tube (1 x 9ml). For engines with 2-10l of oil system.

Full treatment of Petrol/LPG engines requires three-step treatment procedure, according to treatment scheme. We advise you to always use three tubes x 9ml each.

Product is certified.

• Repairs and protects any modification of petrol engines during regular operation.
• Restores engine power and reduces exhaust emissions.
• Saves fuel.

Included in the box

• One 9ml gel tube;
• may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

• rubbing parts are reconditioned and protected against wear;
• restored geometry of the parts;
• fuel savings at idle up to 30%;
• oil pressure increasing;
• equalizing and increasing of compression in the cylinders;
• engine power approaches up to 100%;
• reduction of noise and vibration by 10 times;
• possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
• reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

• disassembly of engine is not required;
• improvement of engine work as early as in 31-62 miles (50-100 km).

Recommendations

Effectiveness and engine working ability mainly depend not only from the condition of an engine itself, but from many other factors, processes and mechanisms which accompany, participate in and influence its work. For instance, a high consumption of oil could be a result not only of considerable wear of engine parts, but of a untightness of pads, a wear of glands, sticking of rings in the cylinder. That is why while taking a decision to treat your engine you should first of all draw your attention to both typical signs of the wear and general symptoms.

For instance:

• low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
• rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
• engine overheating;
• exhaust silencer smokes;
• loss of power;
• high consumption of fuel;
• decreased pressure and increased oil consumption;
• high vibration and noise.

The treatment of new and normally working engines is considered opportune and effective. Accumulated experience of XADO application is an evidence of as early as possible necessity of prophylactic treatment of such engines. At that new parts become run-in and those with a small wear are quickly reconditioned. Due to an unusually low friction coefficient of a protecting coating being formed internal loads on engine parts decrease, and this fact makes their service life considerably longer. And then if some troubles take place you should look for their causes on “the surface”: a carburetor, an ignition system, fuel quality.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

Certificates

This product complies to the following standards:

• ISO6244
• ASTM D 941, D 1298, D 1481
• ISO 8781
• ASTM D 1743
• ISO 3733

Instructions

Complete Engine Treatment (3 tubes are required)

• Step 1
  Warm engine for 10 - 15 minutes.
  Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.
  
  Start the engine and let it idle for 5-10 minutes.
  Drive as usual for 150-250km or idle your car for 4 hours.
   
• Step 2
  Warm engine for 10 - 15 minutes.
  Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

  Start the engine and let it idle for 5-10 minutes.
  Drive as usual for 150-250km or idle your car for 4 hours.
   

• Step 3
  Warm engine for 10 - 15 minutes.
  Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

  Start the engine and let it idle for 5-10 minutes.
  Drive as usual for 150-250km or idle your car for 4 hours.

  Engine treatment considered complete after 1500km of run. Do not change engine oil until then.
   

High kilometer Restoration Treatment (4 tubes are required )

• Step 1
  Warm engine for 10 - 15 minutes.
  Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

  Start the engine and let it idle for 5-10 minutes.

• Step 2
  Warm engine for 10 - 15 minutes.
  Add 2 remaining 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

  Start the engine and let it idle for 5-10 minutes

Brand new vehicles Treatment

• One Step Process 
  Warm engine for 10 - 15 minutes.
  Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.
  Start the engine and let it idle for 5-10 minutes.

Note!

• Do not change oil for 1500 kilometers, when treatment process is complete.
• The protective cermet coating forms on any operative mechanism with no effect on seals or gaskets.
• If the engine is in critical state, worn parts must be replaced.