Energy For Petrol Engines

enginebooster — Thu, 22 Nov 2007 19:51:28 +1100

Increases energy-conversion efficiency of fuel
Improves engine power
Reduces detonation nocks
Does not change octane level and therefore is safe for valves
Contains high-energy complex components that increase combustion heat of fuel (and improve thermodynamic properties of combustion products).
Enlarges potential reserve of fuel heat energy.

Application:

Add the content into the fuel tank in proportion 1 tube (125 ml) per 40 - 50 L of fuel before fueling.

XADO Petrol Super Saver Pack 3 + 1

enginebooster — Sat, 31 Jan 2009 15:07:35 +1100

What a great deal!!!

Super save with this combo purchase!!!

Pack of 3 (three) tubes (3 x 9ml) for petrol engine + 1 (one) pack (1 x 10ml) aerosol tube for automatic transmission!

Full treatment of Petrol/LPG engines requires three-step treatment procedure, according to treatment scheme. We advise you to always use three tubes x 9ml each.

Products are certified.

Repairs and protects any modification of petrol engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

Three 9ml gel tubes of XADO Revitalizing Gel for Petrol Engine (red).
One 10ml aerosol tube of XADO Revitalizing Gel for Automatic Transmission (navy blue);
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 31-62 miles (50-100 km).

Recommendations

Effectiveness and engine working ability mainly depend not only from the condition of an engine itself, but from many other factors, processes and mechanisms which accompany, participate in and influence its work. For instance, a high consumption of oil could be a result not only of considerable wear of engine parts, but of a untightness of pads, a wear of glands, sticking of rings in the cylinder. That is why while taking a decision to treat your engine you should first of all draw your attention to both typical signs of the wear and general symptoms.

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

The treatment of new and normally working engines is considered opportune and effective. Accumulated experience of XADO application is an evidence of as early as possible necessity of prophylactic treatment of such engines. At that new parts become run-in and those with a small wear are quickly reconditioned. Due to an unusually low friction coefficient of a protecting coating being formed internal loads on engine parts decrease, and this fact makes their service life considerably longer. And then if some troubles take place you should look for their causes on “the surface”: a carburetor, an ignition system, fuel quality.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

About red tubes in this pack

Certificates for revitalising gel (red tubes) for petrol engines

This product complies to the following standards:

ISO6244
ASTM D 941, D 1298, D 1481
ISO 8781
ASTM D 1743
ISO 3733

Instructions for revitalising gel (red tubes) for petrol engines

Complete Engine Treatment (3 tubes are required)

For vehicles with more than 100,000 kilometers or vehicles experiencing problems (average car, SUV or light-duty truck that holds 2-10 Litres of oil)

Step 1
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.
Step 2
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.
Step 3
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.

Engine treatment considered complete after 1500km of run. Do not change engine oil until then.

High kilometer Restoration Treatment (4 tubes are required )

For vehicles with more than 100,000 kilometers in good working condition (average car, SUV or light-duty truck that holds 2-10 Litres of oil)

Step 1
Warm engine for 10 - 15 minutes.
Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Step 2
Warm engine for 10 - 15 minutes.
Add 2 remaining 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes

Brand new vehicles Treatment

For brand new vehicles (average car, SUV or light-duty truck that holds 3-10 L of motor oil)

One Step Process
Warm engine for 10 - 15 minutes.
Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.
Start the engine and let it idle for 5-10 minutes.

Note!

Do not change oil for 1500 kilometers, when treatment process is complete.
The protective cermet coating forms on any operative mechanism with no effect on seals or gaskets.
If the engine is in critical state, worn parts must be replaced.

About blue aerosol can in this pack

Dosage

Automatic transmission capacity, L	5-8	9-12	13-15
Cans, pcs.	1	2	3
Treatment scheme	Once	Once	Once

Treatment procedure for automatic transmissions

Check the fluid level.
Shake the can. Spray the contents of the can into the oil filler neck (vent of the oil gage rod) of the automatic transmission.
Run the car as usual without any restrictions.
Revitalization is completed after 50 hours of mechanism operation (after 1500 km run).

Wear resistance of the protective coating is guaranteed for 1 year.

Note

The sure sign of revitalizing beginning is improvement in mechanism operation (noise reduction and smoother gear shift) as early as the first kilometers of run.
If after 100-200 km run mechanism operation improvement does not occur, the most probable cause is a mistaken diagnostics.

Package

10 ml – aerosol can (Art. XA 10515)

The DWD2 Car's Evaporator System Cleaner (both: Heater & Air Conditioner)

enginebooster — Sat, 18 Apr 2009 13:46:14 +1000

Attack the problem where it begins: In your car's ventilation system. Eliminate foul odors, road grime, nicotine oils, contaminants & irritants with no expensive dismantling.

This product is a unique cleaning solution designed to effectively dissolve road grease, dirt, oils, and debris that accumulate on the evaporator fins in your car. This debris is the source of foul odors circulated by your ventilation system. A mechanic or A/C technician installs our patented nozzle to inject the cleaner into the evaporator core case. It foams up to completely fill the evaporator core and casing where it cleans off bug parts, pet hair, nicotine residue and other contaminants. The Kit includes a can of cleaner, the injector system required to effectively place the cleaner into the ventilation system and instructions

Price does not include installation.

Use one can to treat two cars!!!

You can clean your car's evaporator by injecting the Refresher Treatment through the adapter that becomes a permanent fixture with the initial cleaning. The adapter is placed at a convenient location under the dashboard or under the hood (depending on your vehicle) where you can easily use the Refresher Treatment as often as you need. A single can will last up to 6 months, depending on use.

Package content:

DWD2 Evaporator System Cleaner. 1 x aerosol can, 340g volume.
DWD2 Evaporator Can Original Adaptor (as pictured above).

Attention dealers!

Have your own car services related business?
Express your interest in this product now!

Information about the DWD2 evaporator cleaner

Download Presentation (MS Office Power Point format).
Download product information pages in Adobe PDF format.
Bactericidal lab test results test 1 & test 2 (DWD2 kills 99.9% of all known bacterias).
Before cleaning your own evaporator you might want to look at this instructional YouTube video:
http://www.youtube.com/watch?v=bwov0zcVldk
or simply watch it below:

DWD2 in press

ATTENTION! No international postage available for this item due to aerosol goods postage restrictions.

Energy For Diesel Engine

enginebooster — Thu, 22 Nov 2007 19:45:29 +1100

Increases energy-conversion efficiency of fuel.
Improves engine power
Reduces detonation nocks
Does not change cetane rating and therefore is safe for valves
Contains high-energy complex components that increase combustion heat of diesel fuel (and improve thermodynamic properties of combustion products).
Enlarges potential reserve of fuel heat energy.

Application:

Add the content into the fuel tank in proportion 1 tube (125 ml) per 40 - 50 L of fuel before fueling.

XADO VitaFlush. Motor Oil Flush with added Revitalizant.

enginebooster — Mon, 12 Nov 2007 22:21:41 +1100

VitaFlush formula contains the latest achievement in the sphere of resource-saving technologies – a unique substance of revitalizant (from Latin “vita” – life).
Adding the revitalizant into motor oil gives the possibility to form a cermet coating in the places of biggest wear during normal mode of operation.
Technology is maintained by patents in USA, Russia, Germany, China, SAR and other countries.

Included in the box:

One 430ml metal can (for 7-10l of oil).
Recommended for 2 applications (for average car with 3.5L oil system).;
May include volumized XADO® stickers or other promotional materials.

Why VitaFlush?

Why does VitaFlush contain the revitalizant.
Every time the engine loose together with used oil small particles of metal worn out from different rubbing surfaces (a ring-a cylinder, a shaft journal – a bearing brass, etc.)

Previously that was an irreplaceable loss for the engine itself and it was possible to calculate the coming repair by the quantity of oil drains – so, 4 liters of used oil contain 3 grams of metal approximately. The calculation is very simple – the overhaul by reason of the wear – this is a loss of 60 grams of metal for an engine with 1,800 cc volume! But now when the effect of revitalization has been discovered it turned out that it is possible to give back up to 70% of lost metal!

That is why VitaFlush formula contains the particles of revitalizant, which during a short delay of time find in the oil and bring back almost all nanostructured metal clusters, using them as a building material for epitaxial growth of cermet in the places of possible growth! From now on engine parts will work longer protected by XADO revitalizant!

What gives VitaFlush?

What gives the application of VitaFlush?

Reconditioning and protection against wear of rubbing parts;
Complex purification of all oil system;
Mobility recovery of both oil and compression rings;
Elimination of sticking effect of hydraulic compensator;
Stabilization of oil pump parameters (increased compression);
Purification of crank case ventilation system;
Engine power enhancing.

Detailed application guide available here.

Aquastop

enginebooster — Thu, 22 Nov 2007 19:40:34 +1100

Remover of moisture and ice from fuel/fuel tank.

«AQUASTOP» emulsifies moisture in the fuel.
Moisture is distributed along the full volume of the fuel system and is removed with the fuel from the fuel system during engine operation.
«AQUASTOP» prevents water condensate in the fuel and protects the fuel system from corrosion.
«AQUASTOP» is also applied for quick defrost of car locks and their protection from freezing in winter.

Remover of water from fuel system of gasoline engines.

Add «AQUASTOP» into the fuel filler neck in proportion 1 tube of «AQUASTOP» (10 ml) per 5 L of fuel. Moisture will be removed from the fuel system after fuel consumption under regular operating mode.
For preventive measures (use «AQUASTOP» before the beginning of winter and every time at temperature fall). Add «AQUASTOP» into the fuel tank in proportion 1 tube (10 ml) per 20 L of fuel every time you fuel a car.
For defrosting door locks of a car. Squeeze small amount of «AQUASTOP» into the hole of a car lock. The locks become unfrozen completely in 1-3 min.

XADO gel for Petrol/LPG engine

enginebooster — Fri, 09 Nov 2007 19:21:05 +1100

Single tube (1 x 9ml). For engines with 2-10l of oil system.

Full treatment of Petrol/LPG engines requires three-step treatment procedure, according to treatment scheme. We advise you to always use three tubes x 9ml each.

Product is certified.

Repairs and protects any modification of petrol engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

One 9ml gel tube;
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 31-62 miles (50-100 km).

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

Certificates

This product complies to the following standards:

ISO6244
ASTM D 941, D 1298, D 1481
ISO 8781
ASTM D 1743
ISO 3733

Instructions

Complete Engine Treatment (3 tubes are required)

For vehicles with more than 100,000 kilometers or vehicles experiencing problems (average car, SUV or light-duty truck that holds 2-10 Litres of oil)

Step 1
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.
Step 2
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.
Step 3
Warm engine for 10 - 15 minutes.
Add 1 x 9ml tube of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Drive as usual for 150-250km or idle your car for 4 hours.

Engine treatment considered complete after 1500km of run. Do not change engine oil until then.

High kilometer Restoration Treatment (4 tubes are required )

For vehicles with more than 100,000 kilometers in good working condition (average car, SUV or light-duty truck that holds 2-10 Litres of oil)

Step 1
Warm engine for 10 - 15 minutes.
Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes.
Step 2
Warm engine for 10 - 15 minutes.
Add 2 remaining 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.

Start the engine and let it idle for 5-10 minutes

Brand new vehicles Treatment

For brand new vehicles (average car, SUV or light-duty truck that holds 3-10 L of motor oil)

One Step Process
Warm engine for 10 - 15 minutes.
Add 2 x 9ml tubes of Petrol/LPG Engine Treatment (red tube) to engine oil.
Start the engine and let it idle for 5-10 minutes.

Note!

Do not change oil for 1500 kilometers, when treatment process is complete.
The protective cermet coating forms on any operative mechanism with no effect on seals or gaskets.
If the engine is in critical state, worn parts must be replaced.

XADO Diesel Super Saver Pack 3 + 1

enginebooster — Sat, 31 Jan 2009 15:49:11 +1100

What a great deal!!!

Super save with this combo purchase!!!

Pack of 3 (three) tubes (3 x 9ml) for diesel engine + 1 (one) pack (1 x 10ml) aerosol tube for automatic transmission!

Full treatment of Diesel engines requires three-step treatment procedure, according to treatment scheme. We advise you to always use three tubes x 9ml each.

Products are certified.

Repairs and protects any modification of diesel engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

Three 9ml gel tubes of XADO Revitalizing Gel for Diesel Engine (yellow).
One 10ml aerosol tube of XADO Revitalizing Gel for Automatic Transmission (navy blue);
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 31-62 miles (50-100 km).

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

Diesel engine gels information

Application

Treatment of the engine with the oil system 3-10 liters.

Step 1
Squeeze out the contents of one tube into the oil mouth of the engine warmed up to the running temperature.

Start the engine and let it idle for 5-10 minutes.

Step 2
Do as described in Step 1 after 100-250 km run

Step 3
Do as described in Step 2 after 100-250 km run

Dosage

3 - 10 L Oil systems:
3 tubes (9ml), pcs (total 27 ml)| treatment scheme: 1+1+1
New engines: 2 tubes

11-20 L Oil systems:
6 tubes (9ml), pcs (total 54 ml)| treatment scheme: 2+2+2
New engines: 4 tubes

21 - 30 L Oil systems:
9 tubes (9ml), pcs (total 81 ml)| treatment scheme: 3+3+3
New engines: 6 tubes

Note!

Do not change oil until the end of the treatment!

Revitalization is considered to be completed after 1500 km run.

Treatment can be done at idling (4 hours are equivalent to 200 km run); New engines should be treated in one step – 2 tubes at one time.

The protective cermet coating forms on any operative mechanism; in case the mechanism (engine) is in critical state (wear 100%) worn parts must be replaced.

Automatic transmission aerosol pack information

Dosage

Automatic transmission capacity, L	5-8	9-12	13-15
Cans, pcs.	1	2	3
Treatment scheme	Once	Once	Once

Treatment procedure for automatic transmissions

Check the fluid level.
Shake the can. Spray the contents of the can into the oil filler neck (vent of the oil gage rod) of the automatic transmission.
Run the car as usual without any restrictions.
Revitalization is completed after 50 hours of mechanism operation (after 1500 km run).

Wear resistance of the protective coating is guaranteed for 1 year.

Note

Package

10 ml – aerosol can (Art. XA 10515)

Anticarbon For Engine

enginebooster — Thu, 22 Nov 2007 19:34:54 +1100

This new product will clean up carbon deposit on the cylinder and piston rings without taking off the engine head.

ANTICARBON is designed for fine cleaning of cylinder-piston group of gasoline and diesel engines (including turbo-charged ones) against any kind of contamination (deposits, coke, varnish, tar).
It is not necessary to change motor oil after application. It is safe for catalyst converters, oxygen sensors, mechanical rubber parts and compressors.

ATTENTION!!!

Avoid getting ANTICARBON onto lacquer coatings!
Cover car fenders and hood with a cleaning rag before application.
In case of getting the product into the eyes or on the skin, wash them with large amounts of water.
FLAMMABLE! Do not store and use near open flame.

Results of application:

reduced oil consumption;
improved engine power;
levelling of cylinder compression;
lower level of noise while engine operating;
prevents piston overheating as a result of decrease of heat sink;
reduced level of СО in exhaust gases of the engine;
removal of carbonic deposits from the spark-plugs.

Application mode 1:

Warm up the engine. It should be warm but not hot.
Unscrew plugs (injectors). Disconnect ignition timing sensor, Hall device and commutator.
Squeeze one tube into each cylinder through the plug hole.
Screw the plugs in. Wait for 20 minutes. Unscrew the plugs.
Cover the plug holes with absorbing fabric to prevent from outcoming dirt.
Rotate the engine for some seconds with the starter.
Place the plugs (injectors) into their position.
Start the engine and let it operate at about 3500 rpm during 15 - 20 minutes.

During this time carbon softened remains will be removed through the exhaust system.

Application mode 2:

Squeeze 4 tubes into the oil mouth of the warmed up engine on basis of 40 ml of ANTICARBON per 3-5 L of oil.
Run at idle for 10 - 15 minutes.
Drain oil, change oil filter.

XADO gel for all types of rifle barrels

enginebooster — Thu, 03 Jan 2008 10:59:23 +1100

Application Benefits

increase up to 80% of grouping of the shot on 100 m. target;
enhanced flatness of the trajectory;
enhancing of wear resistance and endurance of the barrel by 10 times;
maximum killing power for the given type of ammunition;
reconditioning and protection against wear of barrel bore surface;
restored geometry of the barrel bore (full obturation).

Package Content

The package contains a full set (Red, Yellow and Green tube) of tubes
The package could be posted as a Gift Set or as separate blister packs
May include promotional items

SMALL ARMS

Problem. As any other mechanism, fire arms have their service life. It is well known that defects in the bore may cause barrel burst and end in severe injury of the shooter. Gunsmiths have always faced the problem of improvement of barrel steel quality. It is still vital today, because gun-making is that very sphere where age-old traditions and up-to-date technologies are entwined.

Solution. XADO-technology is able to restore any mechanisms: simple and complex, small and huge, from clockwork to turbine of atomic power plant - if only motion and friction existed. If one had to give a clear, effective and quick demonstration of XADO-technology essence, he wouldn't find anything better than barrel-charge mating. Here is a perfect combination of all necessary conditions for growing of cermet coating: super-high temperatures, sufficient friction energy, interaction of materials of different strength.

XADO Revitalizant gel for DIESEL Engines. Gift Pack.

enginebooster — Sat, 10 Nov 2007 16:55:33 +1100

Gift Pack (3 x 9ml). For engines with 2-10l of oil system.

Full treatment of Diesel engines requires three-step treatment procedure, according to treatment scheme.

Product is certified.

Repairs and protects any modification of petrol engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

Three 9ml gel tube;
One exclusive XADO keyring;
One XADO catalog;
One XADO car steaker;
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 31-62 miles (50-100 km).

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

XADO Gel for gear box, diff & transfer case

enginebooster — Fri, 09 Nov 2007 19:47:42 +1100

Product is certified.
For manual transmission only!
Restores geometry of the parts. Eliminates pits and scratches on working surfaces. Reduces noise and vibration by 10 times. Makes possible operation after an accidental loss of oil.
Included in the box:

One 9ml gel tube;
may include volumized XADO® stickers or other promotional materials.

Attention!!! The number of blisters required to perform full cycle of XADO treatment depending on the volume of oil system!!! Read here for more details.
Main results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
elimination of pits and scratches on working surfaces;
reduction of noise and vibration by 10 times;
possibility of long operation after an accidental oil leakage.

Main advantages of the treatment

disassembly is not required;
universality;
fast effect.

Recommendations
Although the breakdown of gearbox takes place not very often its repair and disassembly are complicated and expensive. XADO will help and it is still possible to “cure” overheating, difficult gearshift, grinding sounds in the gearbox or the noise of differential but the better way is to do it in advance and not wait for the symptoms of disease.
Application Guide
Browse help pages or contact us with your enquiries.

XADO gel for Diesel Engine

enginebooster — Fri, 09 Nov 2007 19:42:39 +1100

Single tube (1 x 9ml). For engines with 2-10l of oil system.

Full treatment of Diesel engines requires three-step treatment procedure, according to treatment scheme. We advise you to always use three tubes x 9ml each.

Product is certified.

Repairs and protects any modification of petrol engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

One 9ml gel tube;
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 50-100 km.

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

Application

Treatment of the engine with the oil system 3-10 liters.

Step 1
Squeeze out the contents of one tube into the oil mouth of the engine warmed up to the running temperature.

Start the engine and let it idle for 5-10 minutes.

Step 2
Do as described in Step 1 after 100-250 km run

Step 3
Do as described in Step 2 after 100-250 km run

Dosage

3 - 10 L Oil systems:
3 tubes (9ml), pcs (total 27 ml)| treatment scheme: 1+1+1
New engines: 2 tubes

11-20 L Oil systems:
6 tubes (9ml), pcs (total 54 ml)| treatment scheme: 2+2+2
New engines: 4 tubes

21 - 30 L Oil systems:
9 tubes (9ml), pcs (total 81 ml)| treatment scheme: 3+3+3
New engines: 6 tubes

Note!

Do not change oil until the end of the treatment!

Revitalization is considered to be completed after 1500 km run.

Treatment can be done at idling (4 hours are equivalent to 200 km run); New engines should be treated in one step – 2 tubes at one time.

The protective cermet coating forms on any operative mechanism; in case the mechanism (engine) is in critical state (wear 100%) worn parts must be replaced.

XADO gel for individual Cylinders

enginebooster — Thu, 22 Nov 2007 20:13:30 +1100

This product is certified.

For reconditioning of separate cylinders only (recommended after XADO Treatment for engine - in a case if compression in one or two cylinders didn't match the rest of cylinders).

Increases compression in the cylinder. Restores geometry of the cylinder, eliminates scores. Protects against extensive wear during cold start-up.

increases compression in the cylinder;
restores geometry of the cylinder, elimination of scores;
protection of rubbing parts against wear during could start-up;
reduction of noise and vibration;
increase in engine power;
fuel savings;
reduction of CO and CH emissions.

Included in the box:

One 9ml gel tube;
may include volumized XADO® stickers or other promotional materials.

Price inclusive GST 10%.

Main results of the treatment

increased compression in the cylinder;
restored geometry of the cylinder, elimination of scores;
protection of rubbing parts against wear during could start-up;
reduction of noise and vibration;
increase in engine power;
fuel savings;
reduction of CO and CH emissions.

Main advantages of the treatment

disassembly and replacement of parts are not required;
opportunity of selective repair ( reduced compression in one, two etc. cylinders);
immediate results (during the first 30 minutes the compression in the cylinder increases by 21.34- 28.44 psi (1.5-2.0 kgf/cm2).

Recommendations

Piston rings provide the seal between the piston and the cylinder wall for compression. Rings also prevent oil from invading the combustion chamber. If the loss of engine power is accompanied by an increased consumption of fuel, oil and black exhaust smoke, the most probable cause is low compression from worn piston rings or from damage to the cylinder walls.

Applications

vehicles, bicycles, scooters, outboard motors of boats, gasoline saws, lawn-mowers and other engines with pre- mixed fuel and oil system.

For application instructions read this page.

XADO gel for AutomaticTransmission

enginebooster — Sat, 31 Jan 2009 10:52:46 +1100

Product is certified.

For automatic transmission only!

Restores geometry of the parts. Eliminates pits and scratches on working surfaces. Reduces noise and vibration by 10 times. Makes possible operation after an accidental loss of oil.

Included in the box:

One 10ml aerosol tube (navy blue);
may include volumized XADO® stickers or other promotional materials.

Attention!!! The number of tubes required to perform full cycle of XADO treatment depending on the volume of oil system!!! Please read application guide for this product.

Main results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
elimination of pits and scratches on working surfaces;
reduction of noise and vibration by 10 times;
possibility of long operation after an accidental oil leakage.

Main advantages of the treatment

disassembly is not required;
universality;
fast effect.

Recommendations

Although the breakdown of gearbox takes place not very often its repair and disassembly are complicated and expensive. XADO will help and it is still possible to “cure” overheating, difficult gearshift, grinding sounds in the gearbox or the noise of differential but the better way is to do it in advance and not wait for the symptoms of disease.

Application Guide

Dosage

Automatic transmission capacity, L	5-8	9-12	13-15
Cans, pcs.	1	2	3
Treatment scheme	Once	Once	Once

Treatment procedure for automatic transmissions

Check the fluid level.
Shake the can. Spray the contents of the can into the oil filler neck (vent of the oil gage rod) of the automatic transmission.
Run the car as usual without any restrictions.
Revitalization is completed after 50 hours of mechanism operation (after 1500 km run).

Wear resistance of the protective coating is guaranteed for 1 year.

Note

Package

10 ml – aerosol can (Art. XA 10515)

XADO gel for PETROL/LPG Engines. Gift Pack.

enginebooster — Sat, 10 Nov 2007 15:39:23 +1100

Gift Pack (3 x 9ml). For engines with 2-10l of oil system.

Full treatment of Petrol/LPG engines requires three-step treatment procedure, according to treatment scheme.

Product is certified.

Repairs and protects any modification of petrol engines during regular operation.
Restores engine power and reduces exhaust emissions.
Saves fuel.

Included in the box

Three 9ml gel tubes in Gift Box;
Keyring;
Catalogue;
Car sticker;
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
fuel savings at idle up to 30%;
oil pressure increasing;
equalizing and increasing of compression in the cylinders;
engine power approaches up to 100%;
reduction of noise and vibration by 10 times;
possibility of operation (up to 187 miles (300 km)) after an accidental oil leakage;
reduction in CO and CH contents in the exhausts by 2-10 times.

Main advantages of the treatment

disassembly of engine is not required;
improvement of engine work as early as in 50-100 km.

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

The DWD2 Car's Evaporator System Cleaner (both: Heater & Air Conditioner)

enginebooster — Sat, 18 Apr 2009 13:46:14 +1000

Attack the problem where it begins: In your car's ventilation system. Eliminate foul odors, road grime, nicotine oils, contaminants & irritants with no expensive dismantling.

Price does not include installation.

Use one can to treat two cars!!!

Package content:

DWD2 Evaporator System Cleaner. 1 x aerosol can, 340g volume.
DWD2 Evaporator Can Original Adaptor (as pictured above).

Attention dealers!

Have your own car services related business?
Express your interest in this product now!

Information about the DWD2 evaporator cleaner

Download Presentation (MS Office Power Point format).
Download product information pages in Adobe PDF format.
Bactericidal lab test results test 1 & test 2 (DWD2 kills 99.9% of all known bacterias).
Before cleaning your own evaporator you might want to look at this instructional YouTube video:
http://www.youtube.com/watch?v=bwov0zcVldk
or simply watch it below:

DWD2 in press

ATTENTION! No international postage available for this item due to aerosol goods postage restrictions.

XADO for Fuel Equipment (Petrol or LPG). Aerosol can 1x10ml

enginebooster — Thu, 03 Jan 2008 00:18:14 +1100

Restores geometry and protects against wear of electric fuel pumps of all types, injector needles of engines with up to 6L;

Included in the box:

One 10ml aerosol can;
May include volumized XADO® stickers or other promotional materials.

Major results of the treatment:

Restoration of geometry and protection against wear of rubbing parts of electric fuel pumps of all types, injectors and unit injectors;
Reliable protection against low-quality fuel;
Reduced fuel consumption;
Reduced noise and vibration levels;
Engine power enhancing;
Reduced emissions of toxic components.

Main advantages of the treatment

Disassembly is not required;
Universality;
Fast effect.

Directions of use

XADO Grease "Repairing" with XADO Revitalizant. 450ml.

enginebooster — Fri, 09 Nov 2007 20:15:02 +1100

Coefficient of revitalization 80%
Restores geometry of parts
Restores scratches and micro cracks
Eliminates surface damages and corrosion
Reduces noise and vibration

The patented formula of this up to date grease is based on a composition of XADO revitalizant and EP complex (Extreme Pressure). The grease is especially effective for repair of quite worn bearings (up to 10 000 rpm).

PURPOSE

It is recommended for joints and bearings of cars, industrial, agricultural and other equipment with wear up to 80%.

The existing methods of design and manufacture do not allow to take into account all working conditions of this or that assembly, and manufacturing tolerances create still more errors. Thus, imperfect parts start being destroyed from the very first moment of operation. XADO® greases help to exceptionally and originally solve this problem. XADO® grease is a completely unique new product, designed for application in all assemblies and mechanisms which are operated with greases. All XADO® greases will neither liquefy nor expel at angular velocities up to 10,000 rpm The amount of the grease for any particular assembly depends on the design and is specified in the service instructions for these assemblies and mechanisms.

Applications: water pump bearings, hub bearing assemblies, ball supports, steering heads, cross-pieces. In industry - any assemblies and mechanisms where greases are applied.

PROPERTIES

Due to balanced content of high-molecular polymers and special additives, including EP complex, REPAIRING grease XADO shows high adhesive, extreme pressure, water-repellent and anti corrosive properties. This grease can be used in joints and mechanisms where multipurpose and special lithium greases are applied.

The grease is especially effective for repair of quite worn bearings (up to 10,000 rpm). Compensates wear up to 80%.
450ml pack.

Package includes one 450ml tube.

Performance level

NLGI 2.......................................(ASTM D217)
ISO-L-XBCEB 2.......................(ISO 6743-9)
KP3K-20...................................(DIN 51502)

DOSAGE

With pressurized application. Add grease through the zerk until desired grease volume is reached.
Manual application. Remove the old grease and fill 1/2 of bearings volume with REPAIRING grease XADO.

RECOMMENDATIONS

If assemblies require periodical grease changing you should use PROTECTIVE grease XADO later on. Do not use for new assemblies and parts!

APPLICATION

Remove cap and protective seal.
Install cartridge in grease gun.

COMPATIBILITY

Compatible with automotive and industrial lithium greases of all types, can be mixed with them in any proportion.

TECHICAL DATA

Working temperature, °C

Long period..........Up to 130
Short period.........Up to 150

Dropping point, °C.........Up to 180
Rotation speed, rpm.......Up to 10 000.

MANUFACTURER

XADO Ltd
Made in Ukraine

Date of production

20/03/2006

Shelf life

5 years.

Metal Conditioner For Transmission

enginebooster — Thu, 22 Nov 2007 20:07:11 +1100

METAL CONDITIONER® is designed for creating special operating conditions for mechanical transmission units and mechanisms, under which high-efficient multilevel system for protection against wear and overloads is formed.

Recommended for Automatic Transmission.

Application of METAL CONDITIONER® for transmissions allows to:

reduce noise and vibration;
extend life span of transmission parts by 4 times!
decrease fuel consumption of cars with cross-country capacity after treatment of a transmission, transfer box or an axle gear.

METAL CONDITIONER® is formulated on basis of full synthetic polyatomic polymer and a balanced package of antioxidant and extreme pressure additives. Due to the covalent atomic bond polymer molecules are very stable to deconstructive influence of local overloads in the friction area. It allows avoiding contact "METAL - METAL" in the friction area for the whole life span of the oil.

APPLICATION PROCEDURE:

Add METAL CONDITIONER® into transmission oil, it will serve you the whole life span of the oil.

Shake the can.
Spray the content into the oil filler neck of a mechanical transmission, transfer box or an axle gear.
Run the car in a regular operating mode without any restrictions.

Dosage

150 ml (1 can) per 2 L of transmission oil
75 ml of the product (spray during 1 min) per 1 L of transmission oil.

Use the product every time you change oil.

!!! Does not contain fluoropolymers, graphite, ferrous and non-ferrous metals, ceramics, esters. Nontoxic and not flammable.
The product is compatible with any kind of transmission oils and other lubricants for transmissions.

Does not change oil viscosity!

Package:
150 ml - aerosol can

XADO Gel For Small Engines (Moto)

enginebooster — Thu, 22 Nov 2007 07:55:29 +1100

For engines with up to 2l of oil system and with up to 1000cc engine volume
For 2 or 4 stroke engines

for bigger engines additional set(s) may be required.

Product is certified.

Extends engine life by 3 times or more. Increases engine power. Reduces toxic emissions, vibration and noise.Included in the box

One pack of 3x4.5ml gel poaches;
may include volumized XADO® stickers or other promotional materials.

Major results of the treatment

Extension of engine life by no less then 3 times;
Restoration of cylinders, elimination of scores;
Increasing of compression in cylinders;
Protection of rubbing parts against wear;
Fuel savings;
Engine power increasing;
Reduction of toxic emissions;
Reduction of noise and vibration.

Recommended to use in househols equipment.

Recommendations

For instance:

low-pitched dead sound in the lower part of the crank case grows noticeably while the crank-case increases its rotational speed (the wear of main bearings);
rhythmical sonorous metallic sound rises while the load increases (the wear of conrod bearing);
engine overheating;
exhaust silencer smokes;
loss of power;
high consumption of fuel;
decreased pressure and increased oil consumption;
high vibration and noise.

XADO dosage is defined by oil system capacity, which in its turn is proportional to the area of friction pairs.

Metal Conditioner For Engines

enginebooster — Thu, 22 Nov 2007 20:01:42 +1100

Noble Prize in 1996!

Metal conditioner TURBO is a modern nanotechnology product which is designed for complex protection and restoration of friction units of engines (including turbocharged ones), that is why it is called "TURBO". Each drop of metal conditioner TURBO contains billions of bearings formulated from molecules of carbon C60 and molecules of aliphatic hydrocarbons reinforced with halogens.

Round polyatomic molecule С60 was called FULLERENE (in honour of famous American architect B. Fuller who suggested building of openwork dome structures from pentagons and sexangles). The chemists presupposed the existence of such molecules already in 1970ties but these molecules were discovered only in 1985. The discovery of fullerenes was rewarded with Nobel Prize in chemistry.

Since then these unique molecules were used in many branches of science and technique. Tribologists who examine friction and wear process also applied these unique molecules because of their perfect ball-shape! Since the grease contains these balls, sliding friction is impossible. Sliding friction will always turn to rolling friction. It means that friction coefficient decreases by 1000 times! Therefore if this friction reduces - the same happens to the wear and there is a chance to stop mechanism's ageing! Fullerenes have higher density and hardness than diamonds have. That means that С60 molecule can stand extremely heavy loads. The oil film containing metal conditioner TURBO is much stronger; friction parts do not contact with one another even in the case the overloads occur.

Moreover, metal conditioner TURBO contains a thoroughly selected package of chemical compounds. Due to wear compensation it allows realizing the concept of anti-wear friction and in-place repair of units and mechanisms. Surface- and chemically active substances specially added into TURBO formula allow keeping fullerenes on friction surfaces in the most loaded areas.

Thus, roughness is being decreased, tribological characteristics of friction units are improved, vibration and noise disappear. At last, metal conditioner TURBO improves properties of motor oil due to the content of the balanced package of antioxidant, extreme pressure and anti-wear additives. It prolongs life span of motor oil and prevents premature ageing.

Regular application of metal conditioner TURBO ensures:
- increase of engine power and compression;
- decrease of noise and vibration;
- reduction of oil and fuel consumption;
- improvement of car dynamic characteristics;
- engine protection against wear;
- easy cold start;
- decrease of exhaust emission gases;
- engine operation in a case of complete oil leakage.

Instructions.

Add the content into the warmed up engine through the oil inlet neck in proportion 1 tube (125 ml) per 3 - 5 L of motor oil. The most optimal concentration - 3from the oil volume. Admitted over dosage is 50(i.e. up to 4,5from the oil volume). The product possesses gentle cleaning properties promoting piston rings decarbonising. Use metal conditioner TURBO each time you change oil for better results.
The product guarantees increase of engine stability to wear by 2 - 4 times (if you use the product since the car running in).

XADO gel for Fuel Equipment

enginebooster — Mon, 12 Nov 2007 22:08:46 +1100

Restores geometry and protects against wear HPFP (high-pressure fuel pumps) of all types, injectors and unit injectors;

For diesel engines of heavy haulers and for other diesel engines of big capacity the dosage of XADO revitalizant gel for high-pressure fuel pump is calculated according to the chart.

Included in the box:

One 9ml gel tube;
May include volumized XADO® stickers or other promotional materials.

Major results of the treatment:

Restoration of geometry and protection against wear of rubbing parts of HPFP (high-pressure fuel pump) of all types, injectors and unit injectors;
Reliable protection against low-quality fuel;
Reduced fuel consumption;
Reduced noise and vibration levels;
Engine power enhancing;
Reduced emissions of toxic components.

Main advantages of the treatment

Disassembly is not required;
Universality;
Fast effect.

Visit this link to read application guide for this product.

XADO Revitalizant gel for POWER STEERING SYSTEMS

enginebooster — Fri, 09 Nov 2007 19:32:14 +1100

XADO® Revitalizant for the steering pump

Product is certified.

Included in the box:

One 9ml gel tube;
may include volumized XADO® stickers or other promotional materials.

Having once treated a steering pump or any other hydraulic pump you can for a long time forget the troubles concerning its breakdown.

Main results of the treatment

rubbing parts are reconditioned and protected against wear;
restored geometry of the parts;
elimination of pits and scratches on working surfaces;
reduction of noise and vibration by 10 times;

Main advantages of the treatment

disassembly is not required;
universality;
fast effect.

Attention!!! The number of tubes required to perform full cycle of XADO treatment dependant on the volume of steering pump system!!! Read manual for more details.